MathematicsAmerican School of Correspondence, 1903 - Engineering |
From inside the book
Results 1-5 of 14
Page
... Proportion 44 Division of Fractions 21 Decimals : Definitions and System of No- tation 25 Addition 30 Subtraction 32 Elementary Algebra and Mensuration . Multiplication 34 Algebra : Division 36 Symbols of Quantity 3 Symbols of ...
... Proportion 44 Division of Fractions 21 Decimals : Definitions and System of No- tation 25 Addition 30 Subtraction 32 Elementary Algebra and Mensuration . Multiplication 34 Algebra : Division 36 Symbols of Quantity 3 Symbols of ...
Page
... Proportion : Inverse Ratio Proportion : Transforming by Alternation 63 51 ཐྲཎྜ་ g ་ 50 By Addition or Subtraction 16 By Inversion By Substitution 17 By Composition By Comparison 18 By Division Involution : Involution of Monomials Square ...
... Proportion : Inverse Ratio Proportion : Transforming by Alternation 63 51 ཐྲཎྜ་ g ་ 50 By Addition or Subtraction 16 By Inversion By Substitution 17 By Composition By Comparison 18 By Division Involution : Involution of Monomials Square ...
Page
... Proportion 35 Mathematics , Geometry , etc. 3 Antecedents , Consequents , etc. 35 Point , Line , Plane , etc. 3 Alternation , Inversion , Compo- Theorem , Problem , Proposition 3 sition and Division Corollary , Scholium , Hypothesis ...
... Proportion 35 Mathematics , Geometry , etc. 3 Antecedents , Consequents , etc. 35 Point , Line , Plane , etc. 3 Alternation , Inversion , Compo- Theorem , Problem , Proposition 3 sition and Division Corollary , Scholium , Hypothesis ...
Page
... Proportions of Bolts and Nuts 29 Welding 12 Strength of Screw Bolts 30 Tempering 12 Wrenches 31 Copper : 12 Forms of Nuts 31 Hammering , Rolling and An- Forms of Bolt Heads 32 nealing 12 Hook Bolt 33 Aluminum 12 Set Screws 33 Bronze ...
... Proportions of Bolts and Nuts 29 Welding 12 Strength of Screw Bolts 30 Tempering 12 Wrenches 31 Copper : 12 Forms of Nuts 31 Hammering , Rolling and An- Forms of Bolt Heads 32 nealing 12 Hook Bolt 33 Aluminum 12 Set Screws 33 Bronze ...
Page
... Proportions of Gear Wheels : Design of Shafts : 60 Rims Formulæ and Table 61 Thickness Hollow Shafts 61 Breadth Design of Shaft Couplings : 63 Total Depth Formulæ 64 Cross Section of Arms Flange Couplings 65 Number of Arms ***** 32 33 ...
... Proportions of Gear Wheels : Design of Shafts : 60 Rims Formulæ and Table 61 Thickness Hollow Shafts 61 Breadth Design of Shaft Couplings : 63 Total Depth Formulæ 64 Cross Section of Arms Flange Couplings 65 Number of Arms ***** 32 33 ...
Common terms and phrases
algebraic altitude Arithmetic binomial boiler called cancel cent ciphers circumference coefficient column common denominator common multiple contained cube root cubic feet cylinder decimal places decimal point diameter divided dividend division divisor dollars engine equal EXAMPLES FOR PRACTICE exponent expression figure Find the value find two numbers following rule frustum Hence highest common factor horse-power hour ILLUSTRATIVE EXAMPLES improper fraction integer last term lateral area least common multiple miles minuend mixed number monomial multiplicand multiply numerator and denominator obtain parenthesis polygon polynomial pounds preceding prism quotient radius ratio Reduce remainder result second term side slant height Solve the equation square feet square inches square root subtract subtrahend Transposing trial divisor triangle units unknown quantity volume weight whole number write
Popular passages
Page 36 - Every circumference of a. circle, whether the circle be large or small, is supposed to be divided into 360 equal parts called degrees. Each degree is divided into 60 equal parts called minutes, and each minute into 60 equal parts called seconds.
Page 9 - SQUARE MEASURE 144 square inches (sq. in.) = 1 square foot (sq. ft.) 9 square feet — 1 square yard (sq. yd.) 30^ square yards = 1 square rod (sq. rd.) 160 square rods = 1 acre (A.) 640 acres = 1 square mile (sq.
Page 31 - The square of the hypothenuse is equal to the sum of the squares of the other two sides ; as, 5033 402+302.
Page 13 - LIQUID MEASURE 4 gills (gi.) = 1 pint (pt.) 2 pints = 1 quart (qt.) 4 quarts = 1 gallon (gal.) 31| gallons = 1 barrel (bbl.) 2 barrels...
Page 33 - The diameter of a circle is a straight line drawn through the center and terminating in the circumference.
Page 7 - Linear Measure 12 inches (in.) = 1 foot (ft.) 3 feet...
Page 19 - The square of the difference of two quantities is equal to the square of the first minus twice the product of the first by the second, plus the square of the second.
Page 11 - CUBIC MEASURE 1728 cubic inches (cu. in.) =1 cubic foot (cu. ft.) 27 cubic feet = 1 cubic yard (cu. yd.) 128 cubic feet = 1 cord (cd...
Page 56 - A right circular cone or cone of revolution is a cone whose axis is perpendicular to the base. It may be generated by the revolution of a right triangle about one of the perpendicular sides as an axis.
Page 17 - Divide the first term of the dividend by the first term of the divisor, and write the result as the first term of the quotient. Multiply the whole divisor by the first term of the quotient, and subtract the product from the dividend.