| Richard Sennett - Marine engines - 1885 - 750 pages
...bent. The bending strips should not be less than 2 inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel...less than (3) three times the thickness of plate. The tensile stress of the plates not exposed to flame should be about 28 tons, and should not exceed... | |
| Bindon Blood Stoney - Girders - 1886 - 854 pages
...The bending strips should not be less than two inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel...three times the thickness of plate. Tensile Stress, <Jc. — The tensile stress of the plates not exposed to flame should be about 28 tons, and should... | |
| Albert Edward Seaton - Marine engineering - 1886 - 520 pages
...bent. The bending strips should not be less than 2 inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel...less than (3) three times the thickness of plate. conditions as stated herein, but when the minimum tensile stress of shell plates exceeds 28 tons, and... | |
| Sir George Charles Vincent Holmes - Steam engineering - 1888 - 560 pages
...original length. The Board of Trade rules for steel marine boilers require that the tensile strength of plates not exposed to flame should be about 28 tons...should not exceed 32 tons per square inch of section. The tensile strength of furnace, flanging Tensile Strength, Ibs. per sq. inch Name of Metal With grain... | |
| Thomas William Traill - Steam-boilers - 1888 - 500 pages
...bent. The bending strips should not be less than 2 inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel at a distance from each other of not more than three times the thickness of the plate, which test they should bear without cracking. Tensile... | |
| Canada, Harris Harding Bligh - Administrative law - 1889 - 1152 pages
...tempering- strips should not be less than two inches broad and ten iuches long, and they should be bent until they break, or until the sides are parallel at a distance from each other of not more than (o) three times the thickness of plate. (m.) When full allowance over iron is wished, the... | |
| Walter S. Hutton - Mechanical engineering - 1892 - 558 pages
...bent. The bending strips should not be less than 2 inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel...— The tensile stress of the plates not exposed to .lame should be about 28 tons, and should not exceed 32 tons, per square inch of section, and 28 tons... | |
| Johann Phillip Edmond Charles Stromeyer - Steam-boilers, Marine - 1893 - 388 pages
...bending and tempering strips should not be less than 2 ins. broad and 10 ins. long, and they should be bent until they break, or until the sides are parallel at a distance from each other of not more than (3) three times the thickness of the plate. Tensile Strength, &c. — 96. When full allowance... | |
| George Wallace Melville - Marine engineering - 1894 - 902 pages
...10", but should be about 25$ ; if annealed, not less than 20$. Strips 2" wide should stand bending until the sides are parallel at a distance from each other of not more than three times the plate's thickness. Lloyd's. — Tensile strength between the limits of 26... | |
| Richard Sennett - Marine engines - 1898 - 574 pages
...bending and tempering strips should be about 2 inches broad and 10 inches long, and they should be bent until they break, or until the sides are parallel at a distance from each other of not more than three times the thickness of plate. When full allowance over iron is wished the tensile strength... | |
| |