 | 1897 - 614 pages
...in diameter. Overflow pipes from fixtures must in all cases be connected on the inlet side of traps. All earthenware traps must have heavy brass floor...rubber washers for floor connections is prohibited. Earthenware water-closets must be set on marble or slate in all new work, and when it is not impossible... | |
 | William Harvey Birkmire - Building, Iron and steel - 1898 - 376 pages
...cases be connected on the inlet side of traps. All earthenware traps must have heavy brass floor-plates soldered to the lead bends and bolted to the trap...rubber washers for floor connections is prohibited. Earthenware water-closets must be set on marble or slate in all new work, and when it is not impossible... | |
 | James Joseph Lawler - Hot-water heating - 1899 - 424 pages
...covers. 102. Overflow pipes from fixtures must in all cases be connected on the inlet side of traps. 103. All earthenware traps must have heavy brass floor plates soldered to the led bends and bolted to the trap flange, and the joint made gas-tight with red or white lead. The use... | |
 | Pennsylvania. Laws, statutes, etc - Law - 1901 - 1022 pages
...Water-closet Connections with Soil-pipe. Section 45. All earthenware traps must have heavy brass floor-plates, soldered to the lead bends and bolted to the trap flange, and the joint made permanently secure and gas-tight. Water-closets, where Located. Section 46. Water-closets must not... | |
 | International Correspondence Schools - Plumbing - 1906 - 762 pages
...covers. 105. Overflow pipes from fixtures must in all cases be connected on the inlet side of traps. 106. All earthenware traps must have heavy brass floor...trap shall be placed at the foot of main soil and waste pipe lines. 108. The sizes for traps must not be less than those given in the following table:... | |
 | Boston (Mass.). - Building laws - 1907 - 116 pages
...except the required back air pipe where a continuous vent is not practicable. Earthenware traps shall have heavy brass floor plates soldered to the lead...and bolted to the trap flange, and the joint made gas tight with red or white lead. Rubber washers for floor connections shall not be used. Back Air... | |
 | Saint Paul (Minn.). - Ordinance, Municipal - 1908 - 1260 pages
...covers. Overflow pipes from fixtures must in all cases be connected on the inlet side of the traps. All earthenware traps must have heavy brass floor...and bolted to the trap flange, and the joint made tight. No putty or plaster shall be used. No trap shall be placed at the foot of" the main "soil and... | |
 | Massachusetts, Boston (Mass.) - Boston (Mass.) - 1908 - 656 pages
...except the required back air pipe where a continuous vent is not practicable. Earthenware traps shall have heavy brass floor plates soldered to the lead...and bolted to the trap flange, and the joint made gas tight with red or white lead. Rubber washers for floor connections shall not be used. Traps shall... | |
 | Massachusetts - Bills, Private - 1909 - 1078 pages
...except the required back air pipe where a continuous vent is not practicable. Earthenware traps shall have heavy brass floor plates soldered to the lead...and bolted to the trap flange, and the joint made gas tight with red or white lead. Rubber washers for floor connections shall not be used. Back Air... | |
 | Chelsea (Mass.) - Chelsea (Mass.) - 1909 - 216 pages
...except the required back air pipe, where a continuous vent is not practicable. Earthenware traps shall have heavy brass floor plates soldered to the lead...and bolted to the trap flange, and the joint made gas tight with red or white lead. Rubber washers for floor connections shall not be used. No long hopper... | |
| |
Earthenware traps shall have heavy brass floor plates soldered to the lead bends and bolted to the trap flange, and the joint made gas tight with red or white lead. Rubber washers for floor connections shall not be used. 
